Introduction to PVC Tile

Vinyl Tile/Plank-- Pressing machine pressing molding can be formed on the surface in a special embossed tiles,also can registered embossed tiles make for a more more vivid lines. Surface tiles can also be specially treated of extend the useful life,and we are committed to developing new products such as 3D tiles , Elasticity tiles, Weave tiles, Maglev tiles, Stop slide tiles, and Composites tiles .... etc, meet different market needs.

Our Products:

  • V.C. Tile:Through the National Green Building Material and comply with environmental concept.
  • Health Tile:Add far infrared and nano antibacterial ingredient of positive effect on the human body.
  • PVC Accessories:including PVC Wall Base, PVC Step Nosing, PVC Edge Covering, and Welding Rod .... etc.

PVC Tile Construction:

PVC flooring (also known as vinyl strips and tiles) is actually constructed of three layers: the backing, the printed film layer and the top layer.


The backing forms the important base of any PVC floor, because it is this which defines the technical quality of the floor. The backing may be made of pure PVC (the most expensive but best composition, because it is dimensionally stable and reliable), but may also include additional recycled material from untraceable sources. That means lower costs but also less reliability. Often a fibre-glass layer is added to give the product a little more stability. A strong odour often gives away the fact that the product incorporates impure recycled ingredients. mFLOR only uses pure PVC.


The middle film layer is responsible for the appearance of the floor. Because its absorbency is low, printing on PVC film is particularly sharp and vibrant. This is not the case where the printing is on paper (as in the case of laminates), or on to a PVC gel-coat as in the case of PVC floors produced by continuous technology (see below). This deeper and more natural look is one of the reasons for the increasing popularity of PVC flooring.


The top layer serves to protect the product from wear and tear caused by use of the floor. Protective layers are available in a variety of compositions and thicknesses; 0.2 mm is commonly used for domestic applicationsand 0.55, 0.7, 1.0 mm for project-based use.

In addition, the top layer can also be provided with an extra protective layer of polyurethane (PU). In particular this provides protection during transport. All mFLOR floors feature a protective layer of matt polyurethane as standard.

Vinyl composition tiles are an excellent option for high-traffic areas because they are highly durable and easy to maintain, and they are also available at a very low cost. They are applied to a smooth, leveled sub-floor and adhered with a vinyl adhesive.
VCT does not get scratched or damaged very easily from heavy impacts or spills, and it can also be refinished repeatedly with chemical strippers and mechanical buffing equipment whenever it starts looking worn out.
Furthermore, vinyl composition tiles can be easily removed and replaced if they ever get damaged; only the damaged tiles need to be replaced, and the rest of the floor can remain intact.

It is essential that all floor covering and adhesive is conditioned to the site conditions.

Layout or Floor Area:
For best visual appearance, in all aspects, it is best that the installation starts in the centre of the room. Measure and find the centre of 2 opposing walls. Snap a chalk line between the 2. Find the centre of this line and snap a second chalk line across the floor at 90 degrees to it.
Without using adhesive, lay a line of tiles down both lines to the width of the room.


Regularly Maintenance:

  1. Remove all traces of dried adhesive
  2. Sweep or vacuum the floor to remove all dirt and dust
  3. Apply neutral detergent to the manufacturers instructions
  4. Scrub the floor with a blue or green pad to remove any stubborn marks
  5. Remove with a mop, rinse clean and mop dry

Long Term Maintenance:

At least once every 12 months, or sooner if conditions require it. The floor should be stripped of its polish using a stripper diluted to the manufacturers instructions and a scrubbing machine. After rinsing and allowing drying the floor should be polished as detailed above.

  • 登入
  • Register